Gunsmith Punches Technical Info
| Page 8
|
|
|
 Brownells Nylon/Brass Drift Punch 1/4" Aluminum Punch Tip Technical Info
USD 4.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-475-005.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Starter Punches 7/32" Roll Pin Starter Punch Technical Info
USD 3.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Hardened steel punches easily remove roll pins from firearms incorporating these pins. Balled tip helps locate the punch on the pin and protects pin end from damage during removal or installation. Available as a 7-punch set or sold individually, as listed below. Mfg: brownells specs: carbon steel, heat hardened. Set contains 1 each of 1⁄16",5⁄64", 3⁄32", 1⁄8", 5⁄32", 3⁄16", and 7⁄32" diameter punches. High quality gunsmith punches by Brownells. Manufacturer item ID: 732SRSB.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Model 5 .050" (1.3mm) Diameter/Short Length Technical Info
USD 17.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. High quality gunsmith punches by Brownells. Manufacturer item ID: SML003893.
More Details : click here
SEARCH this site : click here
|
|
|
Grace Usa Brass Punch Set 1/16" (1.6mm) Brass Pin Punch Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: For drifting sights, driving pins or fitting parts when marking or scratching the surface can mean the difference between a job well done and disaster. Machined from premium, brass hex. Punch set includes 8 flathead, long shaft punches for driving pins completely out. Mfg: grace usa specs: brass, 5⁄16" (7.9mm) hex stock. Punch set, 8 punches: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16", 7⁄32", ", 5⁄16" dia. High quality gunsmith punches by Grace. Manufacturer item ID: 116BPP.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 1/16" Diameter Roll Pin Holder Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. High quality gunsmith punches by Brownells. Manufacturer item ID: B232RSH.
More Details : click here
SEARCH this site : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Gunsmith Punches Technical Info
|
 Copyright © PrizeGuns.com : 1997 - 2024 : All rights reserved. 140-UNI
|
|
