Gunsmith Files Technical Info
| Page 3
|
|
|
 Apex Tool Group Mill Files Smooth Cut 10" (25.4cm) Technical Info
USD 16.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Made especially for draw-filing and finishing metals. Taper slightly in width, thickness stays the same over the entire length. Both edges are square. Single cut on sides and edges. Mfg: apex tool group specs: 6" (15.2cm), 19⁄32" (7.1mm) wide x 7⁄64" (2.8mm) thick. 8" (20.3cm), 25⁄32" (19.9mm) wide x 9⁄64" (3.6mm) thick. 10" (25.4cm), 31⁄32" (24.6mm) wide x 11⁄64" (4.4mm) thick. High quality gunsmith files by Apex. Manufacturer item ID: 8704.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells File Chalk 6 Pieces Technical Info
USD 6.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Filling file teeth with this chalk is an age old "gunsmith kink"® to prevent "pinning", the buildup of metal chips in the teeth of the file. It increases the effectiveness of the file, extends file life, and produces a smoother, more professional finish. Metal removal is faster and easier, too. An inexpensive time and money saver. For superior results, use file chalk along with a good file card, listed elsewhere. Mfg: brownells specs: 4" (10.2cm) long, 1" (2.5cm) diameter 2 pieces per tube. High quality gunsmith files by Brownells. Manufacturer item ID: 333.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells 65Β° 1911 Dovetail Type Slot Sight Base Files #2 65Β° Sight Base File Technical Info
USD 39.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Designed especially for widening and final fitting after using our 65β° sight base cutter to cut the basic slot. Or, can open up a 60β° slot to proper 65β° angle if changing to a new sight design. Has true parallel cutting edges for precision filing, giving you full control over the angle of the dovetail. One cutting side only, with the other two sides safe, so you can widen or deepen sight slots safely without fear of changing the other dimensions. Mfg: brownells specs: 7" (17.8cm) long. .280" (7.1mm) wide. #1, medium, double-cut. #2, fine, single-cut. High quality gunsmith files by Brownells. Manufacturer item ID: LPTR005.
More Details : click here
SEARCH this site : click here
|
|
|
Friedr. Dick Gmbh Screw Slot Files Screw Equalling File #4 .025 Technical Info
USD 47.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Making screw slots is a delicate operation and only the finest, most precise files will do. These are the ones! six sizes and two styles let you cut even the super-thin european slots. Doing the job right takes both a joint file that cuts only on the edges and won't widen the slot as it deepens, and an equalling file to clean up the slot sides and square the bottom. Available in matched, same-size pairs, 1 joint and 1 equalling. Plus, there's the master screw slot set with all twelve files to cover any slotting job. Individual files also available. Note: these files are very thin and easily bent or broken. Sorry, cannot guarantee. Mfg: friedr. Dick gmbh specs: 5-5/8" (14.3cm) long. Both joint and equalling files of the same no. Are the same thickness. Shipping weight 1/4 lb. High quality gunsmith files by Freed. Manufacturer item ID: 11180630.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Swiss Pattern Barrette Files 6" Barrette #2 Cut Technical Info
USD 38.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: These beautiful little swiss pattern files are made especially for getting into tight places, coming exactly up to right angles, working over dovetails, slots and other precision filing. Flat side has double-cut teeth. Back and edges are safe (no teeth) with edges beveled back on 33β° angle. Taper from maximum width shown below to long point. Mfg: apex tool group specs: 4" (10.2cm), 1/2" (12.7mm) wide. #0 or #1 cut. 6" (15.2cm), 11/16" (17.5mm) wide. #0, #1 or #2 cut. Vkhilfef corresponds to swiss cut no. 1. High quality gunsmith files by Apex. Manufacturer item ID: 35073.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Economy Needle File Set Technical Info
USD 29.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Good quality needle files in assortment of 12 different shapes. Recommended for occasional use, or where professional gunsmith files are not needed or justified. Handy plastic roll case. Knurled handles fit needle file handle. Sold in sets only. Mfg: brownells specs: set contains 1 each of the following shapes: barrette, hand, hand with round edges, warding, crochet, three square, square, half round, round, knife, slitting and crossing. Approximately 5β½" overall length. Shank 2β½" x 1/8" diameter. Fine cut. High quality gunsmith files by Brownells. Manufacturer item ID: 423153.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Mill Files Second Cut 8" (20.3cm) Technical Info
USD 13.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Made especially for draw-filing and finishing metals. Taper slightly in width, thickness stays the same over the entire length. Both edges are square. Single cut on sides and edges. Mfg: apex tool group specs: 6" (15.2cm), 19⁄32" (7.1mm) wide x 7⁄64" (2.8mm) thick. 8" (20.3cm), 25⁄32" (19.9mm) wide x 9⁄64" (3.6mm) thick. 10" (25.4cm), 31⁄32" (24.6mm) wide x 11⁄64" (4.4mm) thick. High quality gunsmith files by Apex. Manufacturer item ID: 8529.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Mill Files Second Cut 10" (25.4cm) Technical Info
USD 15.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Made especially for draw-filing and finishing metals. Taper slightly in width, thickness stays the same over the entire length. Both edges are square. Single cut on sides and edges. Mfg: apex tool group specs: 6" (15.2cm), 19⁄32" (7.1mm) wide x 7⁄64" (2.8mm) thick. 8" (20.3cm), 25⁄32" (19.9mm) wide x 9⁄64" (3.6mm) thick. 10" (25.4cm), 31⁄32" (24.6mm) wide x 11⁄64" (4.4mm) thick. High quality gunsmith files by Apex. Manufacturer item ID: 8673.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells File Starter Set Technical Info
USD 399.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: From sight installation to action refinishing, these are the files, cleaning and storage accessories you need. Combined into one money saving kit are: 19 files, 5 handles, a 6 pack of file chalk, and a cleaning brush. Mfg: brownells specs: kit includes: 1 fine needle file set; 60° sight base, fine cut; 4" barrette, # 1 cut; 8" β½" rd., smooth cut; 8" mill file, smooth cut; 8" hand, smooth cut; 6" pillar, #2 cut; 8" ex. Narrow pillar, #2 cut; 6 pk. File chalk, double-face file cleaner, 3 needle file handles, 2. High quality gunsmith files by Brownells. Manufacturer item ID: 080-803-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Metal Checkering Files 20 Lpi (#00) Technical Info
USD 49.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: The only way to get true, accurate line spacing when checkering backstraps, triggerguards, grip frames, ribs and hammer spurs; anywhere an improved gripping surface is needed. Finer cuts give a nice matting effect to reduce glare and light distortion. Procedure is very similar to wood checkering. Layout your master lines (or use a guide like our .45 checkering guide), then establish the pattern by moving the file a few teeth each time using the previous lines as the guide. Once the pattern is fully laid out, bring to final depth with a 60β° needle file. Mfg: brownells specs: 8" (20.3cm) length x β½" (12.7mm) wide. Cutting area: 6" (15.2cm) x β½" (12.7mm). High quality gunsmith files by Brownells. Manufacturer item ID: 31040.
More Details : click here
SEARCH this site : click here
|
|
|
Friedr. Dick Gmbh Screw Slot Files Screw File Pair #6 .040 Technical Info
USD 88.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Making screw slots is a delicate operation and only the finest, most precise files will do. These are the ones! six sizes and two styles let you cut even the super-thin european slots. Doing the job right takes both a joint file that cuts only on the edges and won't widen the slot as it deepens, and an equalling file to clean up the slot sides and square the bottom. Available in matched, same-size pairs, 1 joint and 1 equalling. Plus, there's the master screw slot set with all twelve files to cover any slotting job. Individual files also available. Note: these files are very thin and easily bent or broken. Sorry, cannot guarantee. Mfg: friedr. Dick gmbh specs: 5-5/8" (14.3cm) long. Both joint and equalling files of the same no. Are the same thickness. Shipping weight 1/4 lb. High quality gunsmith files by Freed. Manufacturer item ID: 249-110-394.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells 60Β° Dovetail Standard Slot Sight Base Files #2 60Β° Sight Base File Technical Info
USD 46.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Specially manufactured, true parallel, 3-square file with only one side cutting, other two sides safe. This means the file can be used to widen dovetail slots in gun barrels without danger of deepening the slot or damaging the edge not being worked on. Being a true parallel file, you have absolute control over the angle of the dovetail, impossible with other type files. Mfg: brownells specs: 7" (17.8cm) long. .284" (7.2mm) wide. #1, medium, double-cut. #2, fine, single-cut. High quality gunsmith files by Brownells. Manufacturer item ID: LPTR003.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Swiss Pattern Barrette Files 6" Barrette #1 Cut Technical Info
USD 42.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: These beautiful little swiss pattern files are made especially for getting into tight places, coming exactly up to right angles, working over dovetails, slots and other precision filing. Flat side has double-cut teeth. Back and edges are safe (no teeth) with edges beveled back on 33β° angle. Taper from maximum width shown below to long point. Mfg: apex tool group specs: 4" (10.2cm), 1/2" (12.7mm) wide. #0 or #1 cut. 6" (15.2cm), 11/16" (17.5mm) wide. #0, #1 or #2 cut. Vkhilfef corresponds to swiss cut no. 1. High quality gunsmith files by Apex. Manufacturer item ID: 31029.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Round Files 3/16" Round File Technical Info
USD 6.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: American pattern, smooth cut round files allow even, gradual metal removal for an outstanding finish. Available in several different diameters to handle a variety of jobs. Mfg: apex tool group specs: steel, round files. 7" (15cm) long x 1⁄8" (3.2cm) or 5⁄32" (3.9cm) dia.; 9" (15cm) long x 3⁄16" (4.7cm), 7⁄32" (5.5cm), or " (6.3cm) dia. High quality gunsmith files by Apex. Manufacturer item ID: 1765.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Swiss Pattern Barrette Files 4" Barrette #0 Cut Technical Info
USD 29.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: These beautiful little swiss pattern files are made especially for getting into tight places, coming exactly up to right angles, working over dovetails, slots and other precision filing. Flat side has double-cut teeth. Back and edges are safe (no teeth) with edges beveled back on 33β° angle. Taper from maximum width shown below to long point. Mfg: apex tool group specs: 4" (10.2cm), 1/2" (12.7mm) wide. #0 or #1 cut. 6" (15.2cm), 11/16" (17.5mm) wide. #0, #1 or #2 cut. Vkhilfef corresponds to swiss cut no. 1. High quality gunsmith files by Apex. Manufacturer item ID: 35031N.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Metal Checkering Files 25 Lpi (#00) Technical Info
USD 75.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: The only way to get true, accurate line spacing when checkering backstraps, triggerguards, grip frames, ribs and hammer spurs; anywhere an improved gripping surface is needed. Finer cuts give a nice matting effect to reduce glare and light distortion. Procedure is very similar to wood checkering. Layout your master lines (or use a guide like our .45 checkering guide), then establish the pattern by moving the file a few teeth each time using the previous lines as the guide. Once the pattern is fully laid out, bring to final depth with a 60β° needle file. Mfg: brownells specs: 8" (20.3cm) length x β½" (12.7mm) wide. Cutting area: 6" (15.2cm) x β½" (12.7mm). High quality gunsmith files by Brownells. Manufacturer item ID: 3104025.
More Details : click here
SEARCH this site : click here
|
|
|
Apex Tool Group Mill Files Bastard Cut 6" (15.2cm) Technical Info
USD 8.99
(Indicative price - actual current price possibly lower)
Item technical details & specifications: Made especially for draw-filing and finishing metals. Taper slightly in width, thickness stays the same over the entire length. Both edges are square. Single cut on sides and edges. Mfg: apex tool group specs: 6" (15.2cm), 19⁄32" (7.1mm) wide x 7⁄64" (2.8mm) thick. 8" (20.3cm), 25⁄32" (19.9mm) wide x 9⁄64" (3.6mm) thick. 10" (25.4cm), 31⁄32" (24.6mm) wide x 11⁄64" (4.4mm) thick. High quality gunsmith files by Apex. Manufacturer item ID: 8354.
More Details : click here
SEARCH this site : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Gunsmith Files Technical Info
|
 Copyright © PrizeGuns.com : 1997 - 2024 : All rights reserved. 140-UNI
|
|
