Brownells Roll Pin Punches #6 Roll Pin Punch Technical Info
Gunsmith Punches by Brownells
|
Item technical details & specifications: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 25005939.
 Indicative Price: USD 2.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting products : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Roll Pin Punches #2 Roll Pin Punch Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 25001939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Ar 15 Lower Punch Set Technical Info
USD 65.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Safely remove pins without risk of damaging gun's finish handy 7-piece kit contains all the pin punches and roll pin holders necessary to assemble and disassemble an ar-15 lower receiver without damaging the gun's finish or the pins themselves. Our nylon punch won't leave a mark, while our special bolt catch pin punch is uniquely shaped to clear the side of the receiver while you drive the pin. Other punches for hammer/trigger pins, pivot/takedown pins, and triggerguard, plus additional punches for the forward assist pawl pin and gas tube roll pin on the upper receiver. Mfg: brownells specs: contains: bolt catch pin punch, 1/4" pin punch, 1/16" and 5/64"roll pin punches, 1/8" and 3/32" roll pin holders, and non-marring nylon punch. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-001-305.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch Nylon Punch Tip Technical Info
USD 4.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-475-001.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #6 Punch Technical Info
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 25035939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Starter Punch Set Replaceable Starter Punch .060 Dia. Technical Info
USD 11.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: We are constantly encouraging you to always use starting punches to break tight pins loose, then use a "drift" or pin-punch to drive the pin the rest of the way out. This saves bending pin punches, but much more importantly, it prevents fine guns from getting pin punch mars should the pin punch bend and slip, or, break, and scratch. To bring you the best possible starter punches, we have had special, short replaceable pins made up to fit our famous gunsmith's replacement punch set handles. Their regular use will definitely improve your production . . . And your professionalism! mfg: brownells specs: handle 3" (7.6cm) long x 3/8" (9.5mm) diameter. Pins 1" (2.5cm) long. Set includes 3 punches and three pins. Replacement pin sizes: .039" (.99mm) for 3⁄64" (1.2mm) diameter pins. .060" (1.5mm) for 1⁄16" (1.6mm) diameter pins; .091" (2.3mm) for 3⁄32" (2.4mm) diameter pins. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-513-060.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches Set Of Four Steel Punches Technical Info
USD 35.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4 from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 080-000-034.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #7 Punch Technical Info
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 25036939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 1/16" Diameter Roll Pin Holder Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. High quality gunsmith punches by Brownells. Manufacturer item ID: B232RSH.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch 5/16" Brass Punch Tip Technical Info
USD 3.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-475-002.
More Details : click here
SEARCH this site : click here
|
|
|
Starrett #565 Pin Punch Set Starrett Pin Punch 5/32" Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Precision ground from specially selected tool steel, hardened and highly polished, the starrett pin punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly. Mfg: starrett specs: 4" (10.2cm) long. Sizes: 1/16" (1.6mm), 3/32" (2.4cm), 1/8" (3.2mm), 5/32" (4.0mm), 3/16" (4.8mm), 7/32" (5.5mm), βό" (6.3mm) and 5/16" (7.9mm). High quality gunsmith punches by Starrett. Manufacturer item ID: 52581.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch 1/4" Aluminum Punch Tip Technical Info
USD 4.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-475-005.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Roll Pin Punches #6 Roll Pin Punch Technical Info
|
 Copyright © PrizeGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
