Brownells Hole Center Punches #10 Hole Center Punch Technical Info
Gunsmith Punches by Brownells
|
Item technical details & specifications: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-732-010.
 Indicative Price: USD 3.99
(for Actual Current Price, possibly lower,
please click below)
More Info & Supplier : click here
For more high specification gun & shooting products : click here
|
Try Search on this site - find exactly what you need! Click below:
|
|
|
|
 |
|
|
|
Brownells Nylon/Brass Drift Punch Basic Nylon/Brass Punch Set Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-475-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Hole Center Punches Set Technical Info
USD 21.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: 3 special center punches with outside diameters (o.D.) that match the clearance drill size of the most popular sight, rib and scope base mounting screws. Ground, parallel-sided punches reach through even the thickest handgun rib. Ends guess-work and hole center-to-center spacing problems. To use: level gun in vise or scope mounting jig, position and level sight, rib or base, and clamp in place. Place correct size punch in hole and lightly tap with a 4-oz. Hammer. Remove base; drill and tap first hole; re-install base and check positioning. If everything is "square", re-clamp and finish other holes. Mfg: brownells specs: 2-βύ" (7.0cm) long. ß?" (6.3cm) dia. Knurled handle. Hardened, tool steel. Set contains one of each size. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-732-000.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Nylon/Brass Drift Punch 6 Way Nylon/Brass Punch Set Technical Info
USD 22.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Great combination punch for gunsmith, machinist and toolmaker. Hi-impact steel handle with knurled grip for easy holding and accurate control. Built to withstand maximum impact with a minimum of distortion. Interchangeable and replaceable tips are available in: 5/16" nylon with steel reinforcing pin to prevent bending or breakage while giving completely mar-free punching action; brass in various diameters for a harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Aluminum in two diamters for harder-than-nylon but softer-than-steel impact where slight discoloration is acceptable. Remington shotgun punch tip which is .165" di mfg: brownells specs: handle is 3" (7.6cm) long x 3.8" (9.5mm) diamter. Tips are 1βό" (3.2cm) long. High quality gunsmith punches by Brownells. Manufacturer item ID: 080-475-106.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Model 6 .050" (1.3mm) Diameter/Long Length Technical Info
USD 17.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. High quality gunsmith punches by Brownells. Manufacturer item ID: SML000118.
More Details : click here
SEARCH this site : click here
|
|
|
Lyman Deluxe Hammer & Punch Set Hammer Punch Set Technical Info
USD 53.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Compact set of popular sized punches, with hammer, stores in its own bench block for quick access. Combination brass/nylon hammer has machine knurled handle for positive grip. 4130 steel punches. Mfg: lyman specs: set includes 1/16" (1.5mm), 3/32" (2.3mm), 1/8" (3.1mm), 5/32" (3.9mm), 3/16" (4.7mm) diameter pin punches, 1/8" center punch, 3/16" diameter brass drift. Brass/nylon face hammer, 8" (20cm) overall length, hardwood storage block. High quality gunsmith punches by Lyman. Manufacturer item ID: 7031298.
More Details : click here
SEARCH this site : click here
|
|
|
Grace Usa Roll Pin Punches Brass Roll Pin Punch Set 8 Pc Technical Info
USD 33.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: For drifting sights, driving pins or fitting parts when marking or scratching the surface can mean the difference between a job well done and disaster. Machined from premium, brass hex. Roll pin punch set includes 8 roll pin punches with ends that fit around roll pins without drifting off. Mfg: grace usa specs: brass, 5⁄16" (7.9mm) hex stock. Punch set/roll pin punch set, 8 punches: 1⁄16", 3⁄32", 1⁄8", 5⁄32", 3⁄16", 7⁄32", βό", 5⁄16" dia. Starter punch set, 4 punches: 1⁄16", 3⁄32. High quality gunsmith punches by Grace. Manufacturer item ID: BRP8.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Alignment & Push Punches .092" Diameter Brass Technical Info
USD 8.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: For the professional and home gunsmith alike these punches take much of the frustration out of aligning parts and assemblies. And they provide faster and easier disassembly, too. Furnished with a large, easy-to-grasp, handle that gives excellent control for aligning holes and starting pins. Slightly undersized shank provides a close fit that won't bind in the hole. A slight taper, 3⁄4" from the end is especially useful when fitting parts that require repeated assembly and disassembly. Four sizes fit the majority of pins found on the ar-15, 1911 auto, remington 870 and ruger revolvers. Won't roll off bench. Alignment/push punch set includes one each of the punches liste mfg: brownells specs: handle, plastic. Shank, unhardened steel drill rod, or 360 alloy brass . 3ß?" (8.2cm) long. Oal, 4βύ" (12.1cm) long. Alignment/push punch set, contains (4) brass and (4) steel punches, (1) brass and (1) steel of each diameter: .092" (2.3mm), .120" (3mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 080-000-024.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Punches #4 Roll Pin Punch Technical Info
USD 6.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: With these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping. Mfg: brownells specs: kit includes one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2.0mm); #3, 3/32" (2.4mm); #4, 1/8" (3.2mm); #5, 5/32" (4.0mm); #6, 3/16" (4.8mm); #7, 7/32" (5.5mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 25003939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Premium Roll Pin Holders 3.5mm Diameter Roll Pin Holder Technical Info
USD 4.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Brownells roll spring (pin) holders are accurately drilled to hold tiny roll springs so perfect alignment is obtained. The 1/16" roll spring (pin) holder is notched to clear m16/ar-15 rear sights. The 3.5mm is excellent for holding the pin that retains the breech block on sig handguns. This fine set has sizes 1/16" (notched), 5/64", 3/32", 1/8", 3.5mm and each made from 5/16" hex high carbon 5160 steel that is bainite heat treated for strength. Single groove in grip section and laser marked for quick identification. 100% made in the usa. Mfg: brownells. High quality gunsmith punches by Brownells. Manufacturer item ID: B35RSH.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Roll Pin Starter Punches #2 Punch Technical Info
USD 7.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Start the removal of roll or spring pins without causing damage to the pins or the punch. Short shaft starter punch gives you more control by putting your hand closer to the pin and keeps you from bending longer finishing roll pin punches. Made from solid steel, with parallel-ground shanks and knurled handles. Mfg: brownells specs: steel, black. Kit contains one each of seven sizes: #1, 1/16" (1.6mm); #2, 5/64" (2mm); #3, 3/32" (2.4mm), #4, 1/8" (3.2mm); #5, 5/32" (4mm); #6, 3/16" (4.8mm); 7/32" (5.5mm); #7, 7/32" (5.5mm). High quality gunsmith punches by Brownells. Manufacturer item ID: 25031939.
More Details : click here
SEARCH this site : click here
|
|
|
Brownells Cup Tip Punches Model 5 .050" (1.3mm) Diameter/Short Length Technical Info
USD 17.99
(Indicative price - actual current price possibly lower)
Gunsmith Punches Technical Info
Item technical details & specifications: Eight concave "cupped" tip punches to precisely fit the round head pins found on smith & wesson handguns. Won't flatten the pin top and ruin the gun's looks. Made to the same specs as those used by the factory. Use 3mm punch on sig handguns. Complete set (set d listed below) includes a delrin bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644. Mfg: brownells specs: punches, steel. 5/16" (7.9mm) wide hex handle. .057" (1.44mm)/long; .066" (1.7mm)/long; .072" (1.8mm/long; .040" (1mm)/short; .050" (1.3mm)/short; .050" (1.3mm)/long; 3mm (.118")/long; 3mm (.118")/short. Bench bl. High quality gunsmith punches by Brownells. Manufacturer item ID: SML003893.
More Details : click here
SEARCH this site : click here
|
|
|
|
|
|
Try Search on this site - find exactly what you need! Click below:
|
|
Item on this page: Brownells Hole Center Punches #10 Hole Center Punch Technical Info
|
 Copyright © PrizeGuns.com : 1997 - 2026 : All rights reserved. 140-UNI
|
|
